CarObdCode.Com

0

P0135 Mitsubishi O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1

Author: carobdcode/Categories: Mitsubishi/Time: 2013-08-14 06:42
129

P0135 Mitsubishi O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1

Possible causes
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit poor electrical connection
- Faulty Engine Control Module (ECM)
Tech description
The code means that there is a problem with the heater element circuit of the heated oxygen sensor. The control module monitors how long it take the sensor to warm up and start sending an adequate signal. The code is triggered when the sensor is taking too long to warm up. Water getting inside the heated oxygen sensor connector can caused the heated oxygen sensor fuse to blow. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors. If the sensor and connector are OK, replacing the O2 Sensor 1 usually takes care of the problem
What about the obd code?
Current amperage in the front heated oxygen sensor heater circuit is out of the normal range. (An improper voltage drop signal is sent to ECM through the front heated oxygen sensor heat
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible higher than usual fuel Consumption
P0135 Mitsubishi Description

Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECM controls the heater element circuit by allowing current flow to ground.

The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.

Mitsubishi Vehicle:Mitsubishi Aspire,Mitsubishi Airtrek,Mitsubishi Adventure,Mitsubishi Galant,Mitsubishi Tredia,Mitsubishi Strada,Mitsubishi RVR,Mitsubishi Pajero,Mitsubishi Outlander,Mitsubishi Montero Sport,Mitsubishi Mirage,Mitsubishi Libero,Mitsubishi Legnum,Mitsubishi Lancer,Mitsubishi i Miev,Mitsubishi GTO,Mitsubishi FTO,Mitsubishi Eterna,Mitsubishi eK,Mitsubishi Eclipse,Mitsubishi Diamante,Mitsubishi Delica,Mitsubishi Cordia,Mitsubishi Chariot,Mitsubishi Challenger,Mitsubishi Carisma,Mitsubishi Eclipse,Mitsubishi Endeavor,Mitsubishi Galant,Mitsubishi Lancer,Mitsubishi Outlander,Mitsubishi Raider,

Note:

1. Need to look up additional OBD-II Trouble Codes(DTC), use the search box. Enter the 5 character trouble codes in the search box and submit the search. You can repeat the search as many times as you need, one diagnostic code per search.
2. Don't assume a particular OBDii code means the same for other automotive manufacturers as there are many manufacturer specific codes in use.
3. If your trouble codes are for a different automotive, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other manufactures. The search only looks at OBD codes valid for the currently selected manufacturer.
4. This code is for reference only.
5. Help us improve CarObdCode.com. Tell us fix the code. Any information is appreciated. Thanks.

Leave a Reply