B1B88 Jeep OBD Code Diagnostic Procedure

B1B88 Jeep OBD Code

PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT LOW

For a complete wiring diagram Refer to Section 8W.

When Monitored:

While the CAN bus ignition status is in IGN_RUN, the module checks the sensor input ranges.

Set Condition:If the module detects that the sensor input is less than 3.4 ?0.6% of the (R701) Seat Weight Sensor 5 Volt circuit voltage. This DTC will also set if the (R701) Seat Weight Sensor 5 Volt circuit
is shorted to ground. However, this condition would prevent communication with the OCM and cause a Lost Communication With OCM DTC to set in other modules. Also, this DTC will remain active after the condition
that set this fault is no longer present. This condition is referred to as latching the DTC for the ignition cycle. Cycling the ignition key will change the status from active to stored if the condition
that set the fault is no longer present.

Possible Causes

ACTIVE B1B88 DTC AND B1B89 DTC AT THE SAME TIME

PASSENGER SEAT HARNESS IMPROPERLY ROUTED

PASSENGER SEAT HARNESS WIRES CHAFED, PIERCED, PINCHED, PARTIALLY BROKEN

PASSENGER SEAT HARNESS CONNECTOR TERMINALS BROKEN, BENT PUSHED OUT, SPREAD, CORRODED, CONTAMINATED

(R706) RT-RR SEAT WEIGHT SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

(R706) RT-RR SEAT WEIGHT SENSOR SIGNAL CIRCUIT OPEN

(R701) SEAT WEIGHT SENSOR 5 VOLT CIRCUIT OPEN

RIGHT-REAR SEAT WEIGHT SENSOR

OCCUPANT CLASSIFICATION MODULE (OCM)

Diagnostic Test

1. CHECK FOR ACTIVE INTERNAL FAULTS, IGNITION FAULTS, AND BATTERY FAULTS IN THE OCCUPANT CLASSIFICATION MODULE (OCM)

NOTE:
Ensure that the battery is fully charged.

Turn the ignition on, then off, and then on again.

With the scan tool, read Occupant Classification Module (OCM) DTCs.
Does the scan tool display any active DTCs relating to internal faults, ignition faults, or battery faults?

Yes

Diagnose and repair the DTCs. Refer to the Table of Contents in this Section for a complete list of symptoms.

Go To 2

2. VERIFY THAT DTC B1B88-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT LOW IS ACTIVE

With the scan tool, read OCM DTCs.

Does the scan tool display active: B1B88-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT LOW?

Yes

Go To 3

Go To 10

3. VERIFY THAT DTC B1B88-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT LOW AND B1B89-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT HIGH ARE ACTIVE AT THE SAME TIME

With the scan tool, read OCM DTCs.

Does the scan tool display active: B1B88-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT LOW DTC AND B1B89-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT HIGH DTC AT THE SAME
TIME?

Yes

Perform B1B89-PASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT HIGH diagnostic test.

Go To 4

4. INSPECT PASSENGER SEAT HARNESS WIRES AND CONNECTORS

WARNING:
To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Using the wiring diagram / schematic as a guide, inspect the Passenger Seat Harness wiring and connectors. Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.

Are any of these conditions present?

Yes

NOTE:
Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
Replace the Passenger Seat Harness in accordance with the Service Information.
Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1.

Go To 5

5. VERIFY THAT PASSENGER SEAT HARNESS IS ROUTED CORRECTLY

Verify that the Passenger Seat Harness is routed correctly.

Is the Passenger Seat Harness routed correctly?

Yes

Go To 6

Reroute the Passenger Seat Harness as necessary.

Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1.

6. CHECK VOLTAGE OF (R701) SEAT WEIGHT SENSOR 5 VOLT CIRCUIT

Disconnect the Right-Rear Seat Weight Sensor connector.

WARNING:
To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.

Measure the voltage of the (R701) Seat Weight Sensor 5 Volt circuit.

Is the voltage above 4.8 volts?

Yes

Go To 7

Go To 9

7. CHECK (R706) RT-RR SEAT WEIGHT SENSOR SIGNAL CIRCUIT FOR A SHORT TO GROUND

WARNING:
To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Disconnect the OCM C2 connector.

Measure the resistance of the (R706) RT-RR Seat Weight Sensor Signal circuit between ground and the OCM C2 connector.

Is the resistance below 5.0 ohms?

Yes

NOTE:
Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
Replace the Passenger Seat Harness in accordance with the Service Information.
Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1.

Go To 8

8. CHECK (R706) RT-RR SEAT WEIGHT SENSOR SIGNAL CIRCUIT FOR AN OPEN

Measure the resistance of the (R706) RT-RR Seat Weight Sensor Signal circuit between the OCM C2 connector and the Right-Rear Seat Weight Sensor connector.

Is the resistance below 5.0 ohms?

Yes

Replace the Right-Rear Seat Weight Sensor in accordance with the Service Information.

Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1. If DTC B1B88朠ASSENGER SEAT WEIGHT SENSOR 1 – RIGHT REAR INPUT CIRCUIT LOW returns active, replace the OCM in accordance with the Service
Information.

NOTE:
Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
Replace the Passenger Seat Harness in accordance with the Service Information.
Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1.

9. CHECK (R701) SEAT WEIGHT SENSOR 5 VOLT CIRCUIT FOR AN OPEN

WARNING:
To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.
Disconnect the OCM C2 connector.

Measure the resistance of the (R701) Seat Weight Sensor 5 Volt circuit between the OCM C2 connector and the Right-Rear Seat Weight Sensor connector.
Is the resistance below 5.0 ohms?

Yes

Replace the OCM in accordance with the Service Information.

Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1.

NOTE:
Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
Replace the Passenger Seat Harness in accordance with the Service Information.
Perform OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST.
Perform AIRBAG SYSTEM VERIFICATION TEST – VER 1.

10. CHECKING STORED OR INTERMITTENT CODES

With the scan tool, record and erase all Airbag System Module DTCs.

WARNING:
To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Using the wiring diagram / schematic as a guide, inspect the related wiring and connectors for chafed, pierced, pinched, and partially broken wires, and for broken, bent, pushed out, corroded,
and contaminated terminals. Repair as necessary.

Reconnect all disconnected components and harness connectors.

WARNING:
To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.

With the scan tool, monitor for active codes while performing the following:

Wiggle the wiring harness and connectors of the related airbag circuit.

Continue the test until either a code becomes active or the problem area is isolated.

In the previous steps you have attempted to recreate the conditions responsible for setting the DTC in question / causing the intermittent condition.

Are any ACTIVE DTCs present?

Yes

Select the appropriate diagnostic procedure from the Table of Contents in this section.

No problem found at this time. Perform the Occupant Classification Module System Verification Test in this Section. Erase all codes before returning vehicle
to customer.